toggle menu

WS200-UMB Smart Weather Sensor

Compact all-in-one weather sensor for measurement of wind direction and speed.

From the WS product family of professional intelligent measurement transducers with digital interface for environmental applications for measuring wind direction and speed. One external temperature or rain sensor is connectable.

  • Wind direction and speed
  • Ultrasonic/Wind
  • Wind detection with birdproof construction. Compact all-in-one weather sensor, low power, heater, maintenance-free operation, open communication protocol.
  • RS485 with supported protocols UMB-Binary, UMB-ASCII, Modbus-RTU, Modbus-ASCII, XDR and SDI-12
  • 8371.1
Request a quote or advice

Advantages of the Smart Weather Sensor WS200

  • Measuring wind direction and speed insusceptibly to bird nesting thanks to roofed construction
  • Built-in data pre-processing, universal interfaces and selectable output protocols
  • Compatible with many commercially available Met/HydroMet dataloggers and PLS systems thanks to an open communication protocol
  • Maintenance-free operation – no moving parts that can wear out
  • Suitable for all climate zones; also for solar-powered automatic meteorological stations

Examples of use of the Smart Weather Sensor WS200

The robust and maintenance-free smart weather sensor WS200 is designed for professional meteorological applications in all climate zones. It delivers reliable data, even in extreme ambient conditions.

Examples of use:

  • Weather observation for road and traffic control systems
  • Automatic weather station / Automatic weather sensor (AWS)
  • PV-Monitoring / Solar Monitoring on photovoltaic farms
  • Hydro-meteorological stations
  • Weather observation for building automation
  • Weather stations at airports, marinas and onboard ships
  • Integration into various other systems/solutions, where environmental data is needed...
EU declaration of conformity - Lufft WS Family
EU declaration of conformity - Lufft WS Family
Firmware - WSXXX
For WSXXX device versions 1 - 29 (see serial number) / Für WSXXX Geräteversionen 1 - 29 (siehe Seriennummer)
Firmware - WSXXX v70
For WSXXX device versions ≥30 (see serial number)
Manual - Lufft UMB Config Tool (EN)
Manual - Lufft UMB Protocol (EN)
Manual - Lufft WSxxx weather sensors
Core User Manual
Software - Lufft - ConfigTool .NET
Version 1.6
Software - UMB Config Tool
User Manual - Lufft Smart Weather Sensors
Extended User Manual
Download as PDF
General
Technical data
Dimensions Ø approx. 150mm, height approx. 194mm
Weight Approx. 0.8kg
Interface RS485, 2-wire, half-duplex
Power supply 11…32 VDC
Power supply 5…11 VDC (electronics with limited precision of measurements)
Power supply 24 VDC +/- 10% (heater)
Power consumption 20 VA (heater)
Operating temperature -50...60°C (with heater)
Operating rel. humidity 0...100% RH
Cable length 10m
Protection level housing IP66
Standards/Regulations Compliant to IEC 61724-1:2017
Mast mounting suitable for mast diameter 60 - 76mm
Wind direction
Principle Ultrasonic
Measuring range 0 ... 359.9 °
Unit °
Accuracy < 3° RMSE > 1.0m/s
Resolution 0.1
Wind speed
Principle Ultrasonic
Measuring range 0 ... 75 m/s
Unit m/s
Accuracy ±0.3m/s or ±3% (0...35m/s) ±5% (>35m/s) RMS
Resolution 0.1 m/s
Download as PDF

WS product family: Communication after protocol change

How to communicate with a WS-Sensor and the UMB-config-Tool if the protocol was changed for example to Modbus or SDI-12?

After a Reset ( switching On/Off the sensor) every WS-Senor will start up for the first 5 seconds in UMB-protocol and the standard baud rate of 19200Bd. Independend to the configured protocol and baudrate settings of the WS-Sensor.

In this first 5 Seconds you will be able to connect via UMB-config-Tool to the WS-Sensor after this first command was send the UMB-protocol will stay for 10 minutes after that it switches back to the original configured protocol. This Time will always be extended to 10 minutes if a new UMB command was send.

WS product family: SDI-12 wiring plan for Device version >= 42

How to connect a WS-sensor with a device version >= 42 (hardware version >=14) to a SDI-12 system?

The wiring plan has changed compared to the wiring plan of older WS-Sensor device versions.
The new wiring plan is:

  • +VDD = brown
  • GND = white
  • SDI12_Signal = yellow
  • SDI12_GND = white

This is also mentioned as a note in the latest WS-sensor manual in the section 8 Connections

Back